When Satellite Positioning Goes Quiet: Why Beacon-Based Positioning Receivers Need a GSPS-Class ADC
Published:2026-11-20 · Technical article
Satellite positioning is easy to take for granted — until the fix degrades. In precision agriculture, an auto-steered tractor or self-propelled sprayer follows its guidance line with centimetre-class repeatability for seeding, spraying and harvesting, and that guidance usually comes from GNSS with a correction service. But satellite signals are weak by the time they reach the ground: they are blocked by tree lines, terrain and buildings, disturbed by interference, and the correction link itself can drop where coverage is poor. When the fix is lost, the machine stops or drifts — in the middle of a sowing window that does not wait.
Ground-based beacon positioning is the established backup: a local network of radio beacons at surveyed positions provides positioning that does not depend on satellites at all. This article looks at the receiver at the heart of such a system, and at why its analog-to-digital converter — a GSPS-class part such as the 14-bit, 2.6 GSPS SXA018 — decides how well the whole system can work.
Position from arrival times: how TDOA works
In a time-difference-of-arrival (TDOA) system, several beacons at known, surveyed positions transmit signals in a coordinated pattern. The receiver timestamps the arrival of each beacon's signal. Because the signal travels at the speed of light, each arrival-time difference between a pair of beacons defines a hyperbola of possible receiver positions; combining several beacons fixes the position. A stationary reference receiver in the network can anchor the solution for moving hosts.
Two consequences follow for the receiver design. First, the position solution is only as good as the timestamps — timing resolution is position resolution. Second, the receiver must capture several beacon signals that may sit anywhere in a wide band, separate them, and timestamp them consistently, capture after capture. That is a wideband digitizing job before it is a computing job.
In practice, the beacons usually transmit inside the same band the receiver already monitors for its other duties, which is why these receivers are typically built as wideband digital receivers first and positioning engines second: the front end and the converter are shared, and the positioning function is extracted in the digital domain.
The sampling grid is the ruler
An ADC sampling at 2.6 GSPS places a sample every 0.385 ns. In that interval a radio signal travels about 11.5 cm, so the raw sampling grid already resolves arrival times at the decimetre level before any processing. Receivers do not stop at the raw grid: cross-correlation and interpolation between samples refine each timestamp well below one sample interval, provided the captured waveform is clean — which is where converter resolution and front-end bandwidth enter the budget. A 14-bit converter gives the correlation the dynamic range it needs when strong and weak beacons are received together.
Clock quality belongs in the same budget. Sampling-clock jitter blurs every timestamp by exactly the same mechanism it degrades SNR in a communications receiver, so the clock source, distribution and supply filtering deserve the same care as the analog front end. A jitter budget drawn up alongside the timing budget — not after it — is what separates a receiver that meets its positioning specification from one that only meets it on a good day.
The dual channels of a part like the SXA018 map naturally onto TDOA architectures: one channel can track the beacon set while the second watches a reference path, or two antenna paths can be digitized coherently in one device. For larger installations — several receiver heads covering a wide working area — multi-chip synchronization keeps the converters on a common time base, so timestamps from different boards remain comparable.
Speed is only half the job
A positioning receiver rarely needs the full captured band all the time. The SXA018's integrated digital downconverter (DDC) and programmable FIR filters extract the beacon channels of interest from the wideband capture and reduce the output data rate, so the FPGA receives only the bandwidth it actually processes instead of the full-rate stream. Fast-detect outputs (FD_A/FD_B) provide hardware threshold flags — useful for signal-presence and overload indication without waiting for software to notice.
The processed data leaves the converter over a standard JESD204B interface, supported by both major FPGA ecosystems. Our own evaluation setup pairs the SXA018 board with a Kintex UltraScale (KCU060) baseboard, and the same link-up flow applies to Intel FPGA designs — a practical point for teams whose existing receiver platform is built on either family. Deterministic, synchronized capture across devices is what makes multi-beacon, multi-receiver timestamping meaningful, and it is designed in at the converter and interface level, not patched in later.
Bring-up follows the same order as the signal chain: configure the converter over SPI, bring up the JESD204B link, then verify dynamic performance. The SXA018 evaluation kit — the application board plus the KCU060 baseboard, driven from a PC with the Visual Analyzer ADC software — supports exactly this sequence, with sample rates configured dynamically from the host and the ADC master clock and analog inputs provided externally. What is proven on the kit transfers directly to the product board, because the interface and the configuration flow are the same.
Migrating an existing AD9689-based receiver
Many wideband receiver designs in the field are built around the AD9689. The SXA018 is a pin-to-pin compatible alternative in the same BGA196 package, which makes it a practical second source — or replacement — without a board redesign. A board respin of a GSPS receiver costs a full development cycle; a pin-to-pin second source costs a validation cycle. Pin-to-pin covers the package and pin assignment; before production migration, work through the same checklist as for any converter substitution:
- Power rails and sequencing: confirm the 1 V / 1.9 V / 2.5 V domains and their ramp order against both datasheets.
- Clocking: verify the sampling-clock input conditions and the jitter budget at 2.6 GSPS.
- JESD204B configuration: lane count, subclass and SYSREF handling must match the FPGA build.
- Register configuration: program the device per the SXA018 datasheet; do not assume a competitor's register script carries over unchanged.
- Validation on samples: re-run the receiver's timing and sensitivity tests on the substituted board before committing to production.
Our FAE team supports this migration with pin-comparison material and bring-up guidance, and an evaluation board with a user guide is available so the link-up can be proven on the bench first. Full parameters are in the SXA018 datasheet (bilingual EN/CN PDF) on the SXA018 product page.